Name | Type | Description |
Reference |
P_SINGLEVALUE
/
IfcIdentifier
|
| Reference | Reference ID for this specified type in this project (e.g. type 'A-1'), Also referred to as "construction type". It should be provided as an alternative to the name of the "object type", if the software does not support object types and no classification reference to a recognized classification system used.
IFC4.3.0.0 DEPRECATION The Reference property is deprecated and shall no longer be used, use attribute Name on the relating type instead.
|
| 参照 | 当該プロジェクトで定義する形式の参照ID(例:A-1)、承認された分類に存在しないときに使用される。
|
|
Status |
P_ENUMERATEDVALUE
/
IfcLabel
/
PEnum_ElementStatus |
| Status | Status of the element, predominately used in renovation or retrofitting projects. The status can be assigned to as "New" - element designed as new addition, "Existing" - element exists and remains, "Demolish" - element existed but is to be demolished, "Temporary" - element will exists only temporary (like a temporary support structure).
|
| 状態 | 要素(主にリノベーションまたは改修プロジェクトにおいて)の状態。 状態は、「新規(New)」-新しく追加される要素。「既存」-要素は存在し、かつ残りもの。「破壊」-要素は存在したが、廃棄されるもの。「一時的」-一時的に存在する要素(一時的にサポートしている構造のようなもの)。
|
|
CrossSectionShape |
P_ENUMERATEDVALUE
/
IfcLabel
/
PEnum_DuctSegmentShape |
| Shape | Cross sectional shape. Note that this shape is uniform throughout the length of the segment. For nonuniform shapes, a transition fitting should be used instead.
|
| 形状 | 断面形状:
この形状は直管を通じて一定である。変形する形状のためには、かわりに変形継手が使用される。(フラットオーバル、角型、丸型 他)
|
|
WorkingPressure |
P_SINGLEVALUE
/
IfcPressureMeasure
|
| Working Pressure | Working pressure.
Pressure classification as defined by the authority having jurisdiction (e.g., SMACNA, etc.).
|
| 圧力クラス | 管轄権を持つ当局(SMACNAなど)によって定義された圧力分類
|
|
PressureRange |
P_BOUNDEDVALUE
/
IfcPressureMeasure
|
| Pressure Range | Allowable maximum and minimum working pressure (relative to ambient pressure).
|
| 圧力範囲 | 許容最大・最小動作圧力(周辺圧力との相対値)
|
|
TemperatureRange |
P_BOUNDEDVALUE
/
IfcThermodynamicTemperatureMeasure
|
| Temperature Range | Allowable maximum and minimum temperature.
|
| 温度範囲 | 許容最高・最低温度
|
|
LongitudinalSeam |
P_SINGLEVALUE
/
IfcText
|
| Longitudinal Seam | The type of seam to be used along the longitudinal axis of the duct segment.
|
| ハゼ | ハゼの種類は、ダクト直管の縦方向に使用するハゼの種類
|
|
NominalDiameterOrWidth |
P_SINGLEVALUE
/
IfcPositiveLengthMeasure
|
| Nominal Diameter Or Width | The nominal diameter or width of the duct segment.
|
| 呼び径・巾 | ダクト直管の呼び径またはダクト巾
|
|
NominalHeight |
P_SINGLEVALUE
/
IfcPositiveLengthMeasure
|
| Nominal Height | The nominal height of the object. The size information is provided in addition to the shape representation and the geometric parameters used within. In cases of inconsistency between the geometric parameters and the size properties, provided in the attached property set, the geometric parameters take precedence.
|
| 呼び高さ | ダクト直管の高さ
|
|
Reinforcement |
P_SINGLEVALUE
/
IfcLabel
|
| Reinforcement | The type of reinforcement, if any, used for the duct segment.
|
| 補強 | ダクト直管に何か使用されている場合の補強種類
|
|
ReinforcementSpacing |
P_SINGLEVALUE
/
IfcPositiveLengthMeasure
|
| Reinforcement Spacing | The spacing between reinforcing elements.
|
| 補強間隔 | 補強要素間の距離
|
|